吸附物式干熱機

◆設備結構特征 Product features

※都具有比較穩定相一致的撒氣的壓力和露點

1.吸塔之高速與的直徑經測試然而精細算，塔床壓力差小，保持了壓縮成氣味粗糙劑5秒的接觸的面積時間間隔，充分滿足產品氣的露點想要。

2.30％的非常吹干劑的余量，使用賠償標準非常吹干劑的自然而然腐蝕，事關非常吹干。

3.大規模發展器，確定氣旋一致使用粗糙劑層，驅除溝流表現。

※二次利用氣量材料耗費小于等于14％

1.有遠見的機筒設置，另存100％的降解脂肪含量，存貯的脂肪含量用在添加回收第一階段的回收氣高溫，提高自己設施的解吸程度，讓 回收更徹底。

2.干熱和復蘇主要包括選擇性平衡方案范文，濕空氣中流走干的降解劑限期果最佳。復蘇氣產品出口含濕量管理在亞飽和的情況，使消音器及排氣管清算通道無結霜現象之慮。

3.可選擇吹干機的運作負荷供需改善粉碎氣的使用量，保證 粉碎氣團連續性維持，粉碎各種壓力低至臨界狀態。

※吹干劑在使用使用年限長

1.合適的的機筒尺碼，使氣體借助太干劑層的流動速度和日子保持著好的模式，積極切實發揮太干劑的能。

2.恰當的系統選配，在暖濕氣浪開始機筒前，經除油補救快速消除暖濕氣浪中內植物油成分物與重廢棄物物，解決干澀劑層受廢棄物。

※專用設備按照了先進高品行直流電動及油路分配器閥和耐用的全電子元器件可c語言編程序保持器，人機對戰程序界面信賴，重新重復提示 雙塔負荷率，間歇期限施工現場可編，恢復出廠設置人設10min。氣動閥門使用時間有50萬次的動作。

※封頭表面作冷熱鍍除銹防銹治理 ，10年不銹跡。

※姿勢精確度、耐熱性增強、實操便捷，怎么安裝不用辦理理論知識。

※Bend it out on the same has the stable pressure and dew point

1. The height and diameter adsorption tower by the experimental results calculated precisely, tower, ensure the small resistance bed compressed gas desiccant 5 seconds contact time, meet the requirements of the finished product angry dew point.

2.30% of the surplus, desiccant used to compensate for the natural aging, ensure desiccant dry.

3. Large diffuser, ensure uniform through the desiccant air layer, eliminate channel flow phenomenon.

※Bend the gas loss less than 14% renewable

1. Excellent barrel design, save 100% of the adsorption quantity of heat, storage quantity of heat is used to increase the regeneration stage again angry temperature, improve equipment desorption ability, make renewable more thoroughly.

2. Dry and regeneration of the reverse convection scheme, wet air through the dry when the adsorbent best effect. Getting angry export moisture content control in the saturated state, the muffler and exhaust passage without concentrations of condensation.

3. According to the operation of the dryer load demand adjust dosage, ensure again angry for stability, regeneration renewable air pressure low to critical.

※Bend desiccant long service life

1. The right of barrel size, make the gas through the desiccant flow velocity and time of layer be the best, give full play to the desiccant performance.

2. The reasonable system configuration, in the air into the barrel, except by the efficient before oil processing timely removal in the air in content and heavy oil pollutant, avoid desiccant layer contamination.

※The equipment adopts bend novel high quality and pneumatic valve electric and advanced and reliable full electronic programmable controller, friendly interface, automatic continuous display of the twin towers, working cycle, the programmable factory set 10 min. The valve life for 500000 times action.

※Bend the cylinder body wall be cold galvanizing antirust processing, 10 years don't rust.

※Bend action, stable performance, accurate, easy operation and installation with no need of foundation.

◆主耍系統參數指標 Main technical parameters